|Place of Origin:||China|
|Minimum Order Quantity:||1 set|
|Packaging Details:||plastic film+carton+plwyood box|
|Delivery Time:||45 days|
|Payment Terms:||L/C, D/A, D/P, T/T, Western Union|
|Supply Ability:||5000 sets pear year|
|Function:||Primary Electrician Trainer Education And Training||Color:||Industrial Grey|
ZE4195 Vocational Education Equipment,
1600mm Vocational Education Equipment,
1.5KVA electrician trainer
ZE4195 Electrical Training Equipment for Primary Electrician Trainer
1 Product overview
This training device includes a variety of types of basic electrical control device and measurement, through the relevant experiment, can be familiar with lighting circuit, motor control circuit, measuring circuit connection methods, such as to master its control principle and control mode, the corresponding knowledge and skills, suits, higher vocational colleges, secondary vocational schools and vocational school related professional teaching and skills training examination.
1. The electrical control line components are installed on the mounting board of the wall board, which is convenient to operate and easy to replace, so as to facilitate the expansion of functions or develop new training; The choice of operation content is typical, practical and scientific.
2. The operating table can be put into use only with the ac power supply of three-phase four-wire;
3. The skills training with the control circuit and the special design of small motor, can simulate the factory in all kinds of electric drive system, can meet the installation, debugging, maintenance electrician, failure analysis and troubleshooting skills training requirements;
4. All the components of the relay contact control line are connected to the terminals via wires. The wiring of the students' wiring is only needed to protect the components; In practice, the line is used to train the process.
5. The output power have the monitor display and short circuit protection function, when training occurs when wrong operation or caused by wrong wiring short circuit, the device can automatic protection, avoid burning fuse and damage electrical appliances, security training smoothly;
6. The training platform has a good safety protection system. The connection between the practical training circuit and the device power supply is connected through the safety socket and high reliable protective sleeve structure pistol, which is safe and fast.
2 Capacity parameters
(1) Input power: three phases, five wires 380V±10% 60Hz
(2) Dimension: 1600mm×800mm×1500mm
(3) Whole capacity: ＜1.5KVA
(4) Weight: ＜360kg
(5) Work condition: environment temperature -10℃～+40℃
relative humidity ＜85%(25℃)
3 Product consist of
3.1 Power control panel
The control screen is an iron double-layer subsurface airtight spray structure, aluminum plastic plate. The main control panel is equipped with resources:
1. Three phase four wires power input, go through electrical rotector, main switch, go through start button, stop button, control contact connet or disconnect, and set emergency stop button.
2. There is a 450V point type AC voltage meter 1 piece on control panel, through band switch can observe three electrical power grid voltage.
3. AC low voltage power supply: equipped with transformer 1 set, AC voltage primary side 220V, secondary side 24V and 6.3V AC voltage, 6.3V for signal indicator light power supply, 26V for the AC power supply of rectifier circuit in energy consumption braking;
4. 4 pieces of 5408 diode, it is usef for dynamic braking rectifying circuit.
5. Three pieces of 75Ω/75W resistor is used for electric motor reduction voltage starting,one piece of 10Ω/25W is used for dynamic braking of asynchronous motor.
3.2 Training workbench
The actual training table is an iron double layer subglazed structure, the tabletop is fireproof, waterproof, wear-resistant high density plate, the structure is firm, the modelling is beautiful and generous. There are two drawers (with a lock) on the left and right sides of the table, with cabinets, which can be used to place the hanging pieces and the actual training items, and the structure is strong and beautiful.
3.3 Training components hanging box configuration
(1) Breaker and contactor module
This module contains 2P residual-current circuit breaker (RCCB), fuse socket and three pieces of contractor. It is used for wire three phases motor control circuit, see below photo:
(2) mutual inductor module
This module contains three pieces of 30/5 mutual inductor, three pieces of current meter, components wire to terminal socket. And finish one piece of current mutual inductor is used for single phase circuit control circuit wire and three pieces current mutual inductor circuit wire experiment, see below photo:
(3) Single phase watt hour meter module
This module contains single phase watt hour meter and knife switch, components wire connect to wire terminal. It can finish single phase watt hour meter directly wire circuit, connect to the circuit directly, single phase watt hour meter go through current mutual inductor wire circuit etc. experiment. See below photo
(4) Three phases watt hour meter module
This module contains three - phase watt hour meter and terminals, and the device wiring leads to the terminal. Can complete three-phase three-wire active watt hour meter connection electric circuit, three-phase three-wire active watt hour meter by the current mutual inductor circuit wiring, three-phase four-wire active watt hour meter wiring circuit experiment, as shown in the figure below,
(5) fluorescent lamp and switch module
This module consists of three pieces incandescent lamps, two dual-control switches, and device wiring lead to the terminals. The wiring and control of the fluorescent lamp line can be completed, as shown in the figure below,
4. Complete training contents
1. Single-phase start stop control circuit
2. Asynchronous motor inching control circuit
3. Asynchronous motor two position control circuit
4. Asynchronous motor interlocking forward and reverse control circuit
5. Dual sides interlocking control circuit
6. Automatic sequence control circuit
7. Start manually sequence control
8. Asynchronous motor star and triangle control circuit
9. Energy braking control circuit of asynchronous motor
10. Wiring of the fluorescent lamp circuit
11. Single phase watt hour meter direct wiring circuit
12. The wiring circuit of single phase watt hour meter go through current mutual inductor
13. Voltage meter and current meter wiring circuit
14.The voltage meter of the universal switch is measured in three-phase voltage connection
15. A current mutual inductor is used for the control circuit wiring of the single-phase loop
16. Three pieces current mutual inductance circuits
17. The wiring active circuit of watt hour meter with three phase three lines
18. Three - phase three - line active watt hour meter wire circuit go through current mutual inductor
19. The wiring active circuit of the three-phase four-wire active watt hour meter
Arrange delivery within 45 days upon receipt of payment.
Please see below photo for detailed package.
Training Room Photo
We supply professional educational training equipment and technical teaching equipment, which has been widely applied in Engineering Universities, Polytechnics, Technical Institute, Vocational Schools as well as Industry workforce Development Programs and Training Center. Our products allow students to learn and experiment through valuable hands-on experience, and the technology covered by our training equipment provides knowledge, experiments and didactic skills development that are of critical importance to today´s and tomorrow´s careers.
Photo for Clients Visiting Factory
We supply supply7*24 hours service, customer design service, OEM service, buyer label service. With professional engineers team and sales team, we assure you good product quality.
Our products takes ISO9001 product management system.
|2||Warranty||1 year, 2 years, 3 years or 5 years according to client requirements|
|3||Package||Plastic film+ carton+ Fine plywood|
|4||Products standard||International didactic equipment standard|
|5||Application range||Educational equipment for university, college, vocational training centers|
|6||Company philosophy||Supply best quality Chinese products to the worldwide schools.|
|7||Self owned brand||Shouldshine, SSEDU, JSS.|
|8||Production time||From 10 days to 60 days according to different items